咨询热线：
0531-89008498网站出售
0531-89008498网站出售
| 冷拔异形钢管化学成分表 | |||||||||
| 标准 | 牌号 | C | Si | Mn | P< | S< | Cr< | Ni< | Cu< |
| GB/T 3094 | 10 | 0.07-0.13 | 0.17-0.37 | 0.35-0.65 | 0.035 | 0.035 | 0.15 | 0.30 | 0.25 |
| 20 | 0.17-0.23 | 0.17-0.37 | 0.35-0.65 | 0.035 | 0.035 | 0.25 | 0.30 | 0.25 | |
| 35 | 0.32-0.39 | 0.17-0.37 | 0.50-0.80 | 0.035 | 0.035 | 0.25 | 0.30 | 0.25 | |
| 45 | 0.42-0.50 | 0.17-0.37 | 0.50-0.80 | 0.035 | 0.035 | 0.25 | 0.30 | 0.25 | |
| Q195A | 0.06-0.12 | ≤0.30 | 0.25-0.50 | 0.045 | 0.050 | - | - | - | |
| Q215A | 0.09-0.15 | ≤0.30 | 0.25-0.55 | 0.045 | 0.050 | - | - | - | |
| 异型钢管_A | 0.14-0.22 | ≤0.30 | 0.30-0.65 | 0.045 | 0.050 | - | - | - | |
| Q295A | ≤0.16 | ≤0.55 | 0.80-1.50 | 0.045 | 0.045 | - | - | - | |
| Q345A | ≤0.20 | ≤0.55 | 1.00-1.60 | 0.045 | 0.045 | - | - | - | |
| Q390A | ≤0.20 | ≤0.55 | 1.00-1.60 | 0.045 | 0.045 | - | - | - | |
| DIN 1629 | St37.0 | ≤0.17 | 0.17-0.37 | 0.35-0.65 | 0.035 | 0.035 | 0.25 | 0.25 | 0.25 |
| St44.0 | ≤0.21 | 0.17-0.37 | 0.50-0.80 | 0.035 | 0.035 | 0.25 | 0.25 | 0.25 | |
| St55 | 0.33-0.41 | 0.17-0.37 | 0.50-0.80 | 0.035 | 0.035 | 0.25 | 0.25 | 0.25 | |
| St52.0 | ≤0.22 | ≤0.55 | ≤1.60 | 0.035 | 0.035 | 0.25 | 0.25 | 0.25 | |
| CK45 | 0.42-0.50 | 0.17-0.37 | 0.50-0.80 | 0.035 | 0.035 | 0.25 | 0.25 | 0.25 | |
| 冷拔异形钢管规格及尺寸偏差表 | |||
| 钢管尺寸(mm) | 允许偏差 | ||
| 普通级 | 高级 | ||
|
边长 |
≤30 | ±0.30 | ±0.20 |
| >30~50 | ±0.40 | ±0.30 | |
| >50~75 | ±0.80% | ±0.70% | |
| >75 | ±1.00% | ±0.80% | |
|
壁厚 |
≤1 | ±0.18 | ±0.12 |
| >1~3 |
+15% -10% |
+12.5% -10.0% | |
| >3 |
+12.5% -10.0% |
±10% | |
| 外圆角半径 | |||
| 壁厚S | S≤6 | 6<S≤10 | S>10 |
| 外圆角半径R | ≤2.0S | ≤2.5S | ≤3.0S |
| 边凹凸度 | |||
| 边长尺寸 |
边凹凸度 min | ||
|
普通级 General |
高级 High | ||
|
≤30 >30~50 >50~75 >75 |
0.20 0.30 0.80% 0.90% |
0.10 0.15 0.50% .60% | |
| 弯曲度 | |||
| 精度等级 | 弯曲度mm/m | 总弯曲度 % | |
|
普通级 高级 |
≤4.0 ≤2.0 |
≤0.4 ≤0.2 | |
| 注：精度等级应在合同中注明，如未注明则按普通级交货 | |||
| 扭转值 | |||
| 钢管边长mm | 允许扭转值mm/m | ||
|
≤30 >30~50 |
≤1.5 ≤2.0 | ||
|
>50~75 >75 |
≤2.5 ≤3.0 | ||
| 冷拔异形钢管力学性能表 | ||||
| 标准 | 钢号 |
抗拉强度 σb（Mpa） |
屈服点 σs（Mpa） |
断后延伸率 δ5 ％ |
| Min | ||||
| GB/T 3094 | 10 | 335 | 205 | 24 |
| 20 | 390 | 245 | 20 | |
| 35 | 510 | 305 | 17 | |
| 45 | 590 | 335 | 14 | |
| Q195 | 315 | 195 | 22 | |
| Q215 | 335 | 215 | 22 | |
| 异型钢管_ | 375 | 235 | 20 | |
| Q295 | 430 | 295 | 22 | |
| Q345 | 510 | 315 | 21 | |
| Q390 | 530 | 390 | 18 | |
